欢迎您！东篱公司
退出
-
申报数据库
-
立项数据库
-
成果数据库
-
项目获奖数据库
中文摘要：
为了研究弯叶片弯角、端弯弯高和端弯弯角三个参数对扩压叶栅流道内的旋涡结构和气动性能所造成的影响大小和交互作用的主次顺序,以环形扩压叶栅为研究对象,通过正交试验设计的方法,对试验结果进行分析。结果表明,存在一个最佳弯叶片弯角以平衡集中脱落涡和壁角涡对叶栅出口总压损失分布的影响;弯叶片弯角的提高会导致壁角涡减弱并且涡核靠向端壁,集中脱落涡增强并且涡核靠向流道中部;旋涡结构的变化进而导致端部高损失区域损失减小并且靠向集中脱落涡涡核,流道中部损失增厚并且向中部收缩。端弯的弯高和弯角对角区的影响明显强于流道中部;壁角涡强度的提高导致端部损失的增加;集中脱落涡涡核向端壁移动,导致流道中部损失向端区扩散,但损失减小有限。
英文摘要：
In order to study the effects and interaction of the dihedral angle,end-bowed height and angle on vortex structure and aerodynamic performance,the result in an annular compressor cascade were analyzed through orthogonal experimental design. The results show the existence of best dihedral angle to balance the effect on exit total pressure loss distribution of concentrated shedding vortex and corner vortex. The improvement of dihedral angle leads to the weakening of concentrated shedding vortex and the vortex core towards the end wall,while concentrated shedding vortex is enhanced and the core of it is close to the middle span. The change of vortex structure makes the loss decrease in the high loss region and the region gets close to the core of concentrated shedding vortex,while the loss of middle span gets thickening and shrinks to the center. The influence of endbowed height and angle is more significant on the end region than on the middle span. The improvement of corner vortex strength makes the loss of end region increase,while the movement of concentrated shedding vortex＇s core leads to the proliferation of loss to the end region from the middle,but the decrease of loss is limited.
同期刊论文项目
同项目期刊论文
patial discretization error in an artificial benchmark model of oblique laser incidence by finite vo
Analysis on capabilities of density-based solvers within Open FOAM to distinguish aerothermal variab
A Second Order Radiative Transfer Equation and Its Solution by Meshless Method with Application to S
Analysis on transient conjugate heat transfer in gap–cavity–gap structure heated by high speed airfl
Numerical simulation of infrared signature emitted by liquid rocket plume using wide band k-distribu
Effect of air temperature on combustion characteristics and NOx emissions from a 0.5 MW pulverized c
Experimental study of the impact of holes-typesuction on the flow characteristics in a high-load com
First-principles molecular dynamics study on temperature-dependent dielectric function of bulk 3C an
Temperature-dependent dielectric function of germanium in the UV-vis spectral range: A first-princip
Characterization of combustion and NOx emissions with respect to over-fire air damper opening in a d
Simulation of flow behavior of particles bycluster structure-dependent drag coefficient model for ch
An effective inversion algorithm for retrieving bimodal aerosol particle size distribution from spec
Study of topology and vortex structure in turbinecascades with tip clearance under differentincidenc
Effect of the anthracite ratio of blended coals on the combustion and NOx emission characteristics o
Experimental study on the characteristics of heat transfer and flow resistance in a turbulent pipe f
Evaluation on cold modeling flow field for a down-fired 600 MWe supercritical boiler with multi-inje
Modeling of a rotational supercavitating evaporator and geometrical characteristics of supercavity i
Annaland Martin van Sint．Hans Kuipers, Dongsheng Wen, Discrete particle modeling of granular tempera
A de？ciency problem of the least squares ？nite element method for solving radiative transfer in stro
Simulation of flow behavior of particles by cluster structure-dependent drag coefficient model for c
Aerodynamic characteristics within a cold small-scale model for a down-fired 350 MWe supercritical u
Numerical simulation of natural convection in a square enclosure filled with nanofluid using the two
Inner and Outer Secondary-Air Distance-Effect Study within a Cold Small-Scale Model of a New Down-Fi
New over-fire air arrangement and its air ratio optimization determined by aerodynamic characteristi
Experimental Study of the Impact of Hole-type Suction on the Flow Characteristics in a High-load Com
Influence of Additional Leading-Edge Surface Roughness on Performances in Highly Loaded Compressor C
Investigation of Positively Curved Blade in Compressor Cascade Based on Transition Model (DOI: 10.15
期刊信息
位置：