位置：成果数据库 > 期刊 > 期刊详情页
响应曲面法在表面粗糙度预测模型及参数优化中的应用
  • ISSN号：1006-2467
  • 期刊名称：上海交通大学学报
  • 时间：2010.4.4
  • 页码：447-451
  • 分类：TG5[金属学及工艺—金属切削加工及机床]
  • 作者机构：[1]上海交通大学机械与动力工程学院,上海200240, [2]上海飞机制造有限公司,上海200436
  • 相关基金：国家自然科学基金资助项目（50935001 U0734007）; 国家科技重大专项课题基金项目（2009ZX04014-041）; 国家高技术研究发展计划（863）项目（2009AA04Z150）
  • 相关项目：微细切削刀具设计理论与微铣钻刀具制造技术基础
作者： 张烘州|明伟伟|安庆龙|陈明|戎斌|韩冰|
关键词： 面心组合设计, 响应曲面法, 表面粗糙度, 等值面, 参数优化, central composite face-centered design, response surface methodology, surface roughness, iso-surface, parameter optimization
中文摘要：

分析了切削速度、进给量和切削深度对表面粗糙度的影响规律,提出了一种车削难加工材料钛合金TC11表面粗糙度的建模方法.采用中心组合设计方法,建立了用于表面粗糙度预测的多元回归模型,运用方差分析检验了该预测模型的拟合度,利用响应曲面法对表面粗糙度建立等值响应曲面,从而可以通过切削参数的优化在保证加工质量的前提下获得更高的材料去除率,实现难加工材料钛合金高效切削.

英文摘要：

This paper presented a study of the development of a surface roughness model for finish turning of TC11.The model was developed in terms of cutting speed,feed rate and depth of cut.The multi-quadratic regression equation predicting formula for surface roughness was established by means of central composite design of experiment,and variance analyses were applied to check the fitting degree of the predictive model.Then the response surface methodology was used to generate response contours of surface roughness.The experimental results indicate that the material removal rate can be improved by selecting optimal cutting parameters without increasing the surface roughness.

同期刊论文项目
微细切削刀具设计理论与微铣钻刀具制造技术基础
期刊论文 108 会议论文 2 专利 18
超高速钻削多层高密度印刷电路板超微细孔加工研究
期刊论文 21 会议论文 34
同项目期刊论文
微型钻针内芯倒锥度测量新方法的研究
微钻刃面图像边缘角点自适应提取方法
Studies on drilling processes of intermetallic compounds
Finite element analysis of cutting force and burr formation in micro-cutting of titanium alloy consi
Experimental investigation on drilling PCB through-holes
Characteristics of chip formation in the micro-drilling of multi-material sheets
微小孔成孔监测技术
印刷电路板超细微孔钻削加工及其关键技术
电路板复合材料高速钻削刀具的磨损
钻削加工的三维建模及可视化
印刷电路板高速数控钻床的特点及关键技术
印制电路板微孔机械钻削研究
1Cr18Ni9Ti平面铣削中倒棱结构对切削性能影响的试验研究
铣削高强度钛合金TC18的刀具磨损机理
Dry turning of rotor steel 26NiCrMoV145 using multilayer coated cemented carbide tools
Study on the modeling method for finite element analysis of chip formation process
Influence of Cutting Parameters on Vibration Acceleration in Micro-end-milling
Model building and interface friction research of micro cutting
Effect of grain refinement and composition on the wear of cemented carbide cutting tools
Analysis of Specific Energy of TC18 and TA19 Titanium Alloys in Surface Grinding
Experimental Study on the Performance of WC-Co Inserts in Turning 4Cr13 Die Steel
Research on the Edge Design Precision PCD Thread Milling Tool
Surface roughness prediction in turning of free machining steel 1215 by artificial neural network
Evaluation of the performance of coated carbide tools in face
Experimental investigation of microdrilling of printed circuit board
Parameters Optimization of Turning Free Cutting Steel Based on the Coupling Method of Response Surfa
锥形球头立铣刀刀刃曲线的光滑过渡
Effective lateral stiffness enhancement of high-aspect-ratio carbon nanotube probe
Failure mechanism of Twist Drill in Vibration Drilling of Duralumin
微细切削刀具及其相关技术研究进展
An investigation on wear mechanism of resin-bonded diamond wheel in Elliptical Ultrasonic Assisted G
Experimental investigation on conventional grinding of Ti-6Al-4V using SiC abrasive
A comparative study of high speed orthogonal turning of AISI4340 by three different finite element m
Investigation of surface integrity in conventional grinding of Ti-6Al-4V
Study on Grinding Machinability of Titanium Alloy Using SiC Abrasive
Experimental investigation on conventional grinding of TC4 and TC11 using SiC abrasive
Analysis on the Microstructure of Carbide Reamers after the Cryogenic Treatment
Surface integrity analysis on high speed end milling of 7075 aluminum alloy
AN EXPERIMENTAL AND FEM STUDY ON DRY TURNING OF ROTOR STEEL 26NiCrMoV145 USING MULTILAYER COATED CEM
Fuzzy Chatter Stability Lobes Model in Milling
Experimental Study on Cutting Characteristics for Buttress Thread Turning of 13%Cr stainless steel
Selection of Minimum Quantity Lubrication (MQL) Parameters in Milling of Ti-6Al-4V
Study on the Machinability of Free-cutting Steels 1214 and 12L15 With Coated Tool
Wear Behavior of Carbide Inserts in Face Milling TA19 Alloy
Experimental research on the high speed drilling of PCB using microdrill
Experimental Research of Grinding TC4 Titanium Alloy Using Green Silicon Carbide Wheel
A solution for micro drill condition monitoring
Research on Fixture Hole Drilling Quality of Printed Circuit Board
Geometry Optimization of D-type Micro End-mill with FEM Analysis
Experimental study on brittle–ductile transition in elliptical ultrasonic assisted grinding (EUAG) o
Surface Integrity of High Speed Milling of Al/SiC/65p Aluminum Matrix Composites
超声振动辅助磨削技术的现状与新进展
积屑瘤状态对微细切削表面轮廓特征的影响
微细铣削振动信号非线性特征的试验研究
硬质合金刀具车削GH2132高温合金磨损及破损试验
An investigation on wear mechanism of high-speed turning of free-cutting steel AISI 1215 using uncoa
Dry Milling of the Ultra-High-Strength Steel 30CrMnSiNi2A with Coated Carbide Inserts
Friction and Wear Performance of Titanium Alloys against Tungsten Carbide under Dry Sliding and Wate
Fabrication of micro DOE using micro tools shaped with focused ion beam
微小型单头错齿滚刀滚齿切削过程建模与仿真
微小型滚刀设计与参数选择
圆弧刃刀具微细非自由切削参数建模与预报
Growth and characterization of Mg(OH)2 film on magnesium alloy AZ31
Formation of an Oxametallacycle Surface Intermeiate via Thermal Activation of 1-Chloro-2-Propanol on
高强度合金硼铸铁组织成分与切削性能研究
滚压印圆柱母光栅的微刻划制造
Fundamental performance of Magnetic compound Fluid(MCF) wheel in ultra-fine surface finishing of opt
Influence Axial Vibration on Lateral Bending Deformation of Twist Drill in Machining Small Hole
Effect of Low-frequency Pulsed Magnetic Treatment on Micro-hardness of High Speed Steel
A reseach of fracture mechanism in micro cutting of 45 steel based on material properties
磁场分布对磁性复合流体抛光材料去除率的影响
Effect of Powder Pretreatment on the Wear of Ultrafine Cemented Carbide Cutting Inserts
Effect of Grain Growth Inhibitor on the Wear of Ultrafine Cemented Carbide Cutting Inserts
新型微细球端铣刀几何建模与优化设计
微细铣削表面粗糙度预测与试验
Carbon Nanotube’s Modification by Focused Ion Beam Irradiation and Its Healing Strategies
基于人工神经网络的铣削加工变形预测模型
微细铣削振动信号特征参数的主成分分析
典型零件车铣复合加工的运动学特征分析
Thermal activation and reaction of allyl alcohol on Ni(100)
Experiment on Glass Microgroove Molding by Using Polycrystalline Nickel Phosphorus Mold
Experimental Study on Micro-milling of Ti6Al4V with Minimum Quantity Lubrication
基于聚焦离子束铣削技术的微刀具制备
Reserch of dislocation theory in micro cutting
双势阱中冷原子的关联隧穿
干式切削和微量润滑条件下的螺纹车削机理分析及试验研究
基于自适应采样距离场的车铣复合加工中刀具—工件接触几何计算
基于DG／K方法的成形铣刀设计模型
脉冲磁场对高速钢刀具材料微观硬度的影响
斜圆柱结构的新型微细球端铣刀的设计与制造
基于无瞬心包络的微细铣刀螺旋槽刃磨分析
1Cr18Ni9Ti平面铣削中倒棱结构对切削性能影响的试验研究
铣削高强度钛合金TC18的刀具磨损机理
芳纶纤维复合材料切削性能与刀具选用
镁基生物医用材料研究进展
铝7075介观尺度切削过程的仿真研究
小直径麻花钻的钻削仿真与实验研究
精密、超精密切削技术发展概况
切削参数对微细立铣削振动加速度的影响
原子非序列双电离的多次返回碰撞电离机理分析
微细立铣削切削振动试验研究
直槽微铣削中切削参数对铣刀跳动量的影响
锥形球头立铣刀刀刃曲线光滑过渡研究
不锈钢精密车削加工硬化研究
复合粉预处理对WC-10Co超细晶硬质合金刀具寿命的影响
微细刀具的深冷处理研究
金刚石刀具的圆柱母光栅微加工基础研究
期刊信息
  • 《上海交通大学学报》
  • 中国科技核心期刊
  • 主管单位:中华人民共和国教育部
  • 主办单位:上海交通大学
  • 主编：郑杭
  • 地址：上海市华山路1954号15F
  • 邮编：200030
  • 邮箱：shjt@chinajournal.net.cn
  • 电话：021-62933373 62932534
  • 国际标准刊号：ISSN：1006-2467
  • 国内统一刊号：ISSN：31-1466/U
  • 邮发代号:4-256
  • 获奖情况:
  • 1996年全国优秀科技期刊奖,1992年、1996年、1999年国家教育部系统优秀科技期刊奖,2002年“百种重点期刊奖”,2003年百种中国杰出学术期刊,2004年教育部全国高校优秀科技期刊一等奖,2004年“百种重点期刊奖”
  • 国内外数据库收录:
  • 美国化学文摘（网络版）,美国数学评论（网络版）,德国数学文摘,荷兰文摘与引文数据库,美国工程索引,美国剑桥科学文摘,英国科学文摘数据库,日本日本科学技术振兴机构数据库,中国中国科技核心期刊,中国北大核心期刊（2004版）,中国北大核心期刊（2008版）,中国北大核心期刊（2011版）,中国北大核心期刊（2014版）,中国北大核心期刊（2000版）
  • 被引量:30903