欢迎您！东篱公司
退出
-
申报数据库
-
立项数据库
-
成果数据库
-
项目获奖数据库
中文摘要：
为改善大安装角扩压叶栅角区流动,应用轴对称端壁造型技术对其端区进行改型设计。采用数值模拟的方法探讨了凹型曲线覆盖长度以及深度对叶栅气动性能的影响,结果表明,在设计冲角以及负冲角下,采用合理的凹型端壁造型方案均可不同程度地降低叶栅端区流动损失和出口落后角度,但在正冲角下,端壁造型曲线选取不当将会提前促发角区失速,恶化端区流场。进一步将凹型轴对称端壁造型技术应用到1.5级压气机中,验证了此种改型方法的有效性,在保证工作范围基本不变的条件下,整机峰值效率提高了0.94%。
英文摘要：
In order to improve the corner flow of a compressor cascade with high stagger angle, the concave axisymmetric endwall molding technology（CAEMT） was applied to redesign its endwall region. The numerical method was adopted to investigate the effects of covering length and covering depth of concave line on the aerodynamic performance of the compressor cascade. As a result,it is found that the different CAEMT schemes can decrease the endwall flow loss and outlet deviation flow angle of the cascade to different extend at negative and design incidences. However,the corner stall will be triggered early and endwall flow will be aggravated at higher positive incidence once improper endwall contouring line is implemented. The CAEMT is further applied into a 1.5 stage compressor to test its effectiveness and the peak efficiency of the compressor increased by 0.94%with a similar operating range.
同期刊论文项目
同项目期刊论文
patial discretization error in an artificial benchmark model of oblique laser incidence by finite vo
Analysis on capabilities of density-based solvers within Open FOAM to distinguish aerothermal variab
A Second Order Radiative Transfer Equation and Its Solution by Meshless Method with Application to S
Analysis on transient conjugate heat transfer in gap–cavity–gap structure heated by high speed airfl
Numerical simulation of infrared signature emitted by liquid rocket plume using wide band k-distribu
Effect of air temperature on combustion characteristics and NOx emissions from a 0.5 MW pulverized c
Experimental study of the impact of holes-typesuction on the flow characteristics in a high-load com
First-principles molecular dynamics study on temperature-dependent dielectric function of bulk 3C an
Temperature-dependent dielectric function of germanium in the UV-vis spectral range: A first-princip
Characterization of combustion and NOx emissions with respect to over-fire air damper opening in a d
Simulation of flow behavior of particles bycluster structure-dependent drag coefficient model for ch
An effective inversion algorithm for retrieving bimodal aerosol particle size distribution from spec
Study of topology and vortex structure in turbinecascades with tip clearance under differentincidenc
Effect of the anthracite ratio of blended coals on the combustion and NOx emission characteristics o
Experimental study on the characteristics of heat transfer and flow resistance in a turbulent pipe f
Evaluation on cold modeling flow field for a down-fired 600 MWe supercritical boiler with multi-inje
Modeling of a rotational supercavitating evaporator and geometrical characteristics of supercavity i
Annaland Martin van Sint．Hans Kuipers, Dongsheng Wen, Discrete particle modeling of granular tempera
A de？ciency problem of the least squares ？nite element method for solving radiative transfer in stro
Simulation of flow behavior of particles by cluster structure-dependent drag coefficient model for c
Aerodynamic characteristics within a cold small-scale model for a down-fired 350 MWe supercritical u
Numerical simulation of natural convection in a square enclosure filled with nanofluid using the two
Inner and Outer Secondary-Air Distance-Effect Study within a Cold Small-Scale Model of a New Down-Fi
New over-fire air arrangement and its air ratio optimization determined by aerodynamic characteristi
Experimental Study of the Impact of Hole-type Suction on the Flow Characteristics in a High-load Com
Influence of Additional Leading-Edge Surface Roughness on Performances in Highly Loaded Compressor C
Investigation of Positively Curved Blade in Compressor Cascade Based on Transition Model (DOI: 10.15
期刊信息
位置：