位置：成果数据库 > 期刊 > 期刊详情页
微小型滚刀设计与参数选择
  • ISSN号：1001-0645
  • 期刊名称：北京理工大学学报
  • 时间：2011
  • 页码：391-393
  • 分类：TG721[金属学及工艺—刀具与模具]
  • 作者机构：[1]北京理工大学机械与车辆学院,北京100081
  • 相关基金：国家自然科学基金资助项目（50875026）
  • 相关项目：微细切削刀具设计理论与微铣钻刀具制造技术基础
作者： 刘佳|周家花|王西彬|
关键词： 微小型滚刀, 有限元分析, 参数选择, micro gear hob, finite element analysis, parameter selection
中文摘要：

为模数小于0.1 mm的微小型滚刀提出了一套完整而准确的设计理论与方法.结合普通滚刀设计方法与经验,运用力学知识和有限元分析对微小型滚刀的设计理论与方法进行探讨.通过实例证明了提出的设计方法的正确性.

英文摘要：

A set of complete and accurate design theory and method is put forward for the micro hob of which the modulus is less than 0.1 mm.Combining the regular method and experience of hob design,this paper gives the preliminary study of design theory and method using mechanics knowledge and finite element analysis.As a result,the design method proposed in this paper is proved the be correct by particular example.

同期刊论文项目
微细切削车刀及齿轮滚刀的设计理论与制备方法
期刊论文 26 会议论文 4 专利 1
微细切削刀具设计理论与微铣钻刀具制造技术基础
期刊论文 108 会议论文 2 专利 18
同项目期刊论文
Dry turning of rotor steel 26NiCrMoV145 using multilayer coated cemented carbide tools
Study on the modeling method for finite element analysis of chip formation process
Influence of Cutting Parameters on Vibration Acceleration in Micro-end-milling
Model building and interface friction research of micro cutting
Effect of grain refinement and composition on the wear of cemented carbide cutting tools
Analysis of Specific Energy of TC18 and TA19 Titanium Alloys in Surface Grinding
Experimental Study on the Performance of WC-Co Inserts in Turning 4Cr13 Die Steel
Research on the Edge Design Precision PCD Thread Milling Tool
Surface roughness prediction in turning of free machining steel 1215 by artificial neural network
Evaluation of the performance of coated carbide tools in face
Experimental investigation of microdrilling of printed circuit board
Parameters Optimization of Turning Free Cutting Steel Based on the Coupling Method of Response Surfa
锥形球头立铣刀刀刃曲线的光滑过渡
Effective lateral stiffness enhancement of high-aspect-ratio carbon nanotube probe
Failure mechanism of Twist Drill in Vibration Drilling of Duralumin
微细切削刀具及其相关技术研究进展
An investigation on wear mechanism of resin-bonded diamond wheel in Elliptical Ultrasonic Assisted G
A comparative study of high speed orthogonal turning of AISI4340 by three different finite element m
Investigation of surface integrity in conventional grinding of Ti-6Al-4V
Study on Grinding Machinability of Titanium Alloy Using SiC Abrasive
Experimental investigation on conventional grinding of TC4 and TC11 using SiC abrasive
Analysis on the Microstructure of Carbide Reamers after the Cryogenic Treatment
Surface integrity analysis on high speed end milling of 7075 aluminum alloy
AN EXPERIMENTAL AND FEM STUDY ON DRY TURNING OF ROTOR STEEL 26NiCrMoV145 USING MULTILAYER COATED CEM
Fuzzy Chatter Stability Lobes Model in Milling
Experimental Study on Cutting Characteristics for Buttress Thread Turning of 13%Cr stainless steel
Selection of Minimum Quantity Lubrication (MQL) Parameters in Milling of Ti-6Al-4V
Study on the Machinability of Free-cutting Steels 1214 and 12L15 With Coated Tool
Wear Behavior of Carbide Inserts in Face Milling TA19 Alloy
Experimental research on the high speed drilling of PCB using microdrill
Experimental Research of Grinding TC4 Titanium Alloy Using Green Silicon Carbide Wheel
A solution for micro drill condition monitoring
Research on Fixture Hole Drilling Quality of Printed Circuit Board
Geometry Optimization of D-type Micro End-mill with FEM Analysis
Experimental study on brittle–ductile transition in elliptical ultrasonic assisted grinding (EUAG) o
Surface Integrity of High Speed Milling of Al/SiC/65p Aluminum Matrix Composites
超声振动辅助磨削技术的现状与新进展
积屑瘤状态对微细切削表面轮廓特征的影响
微细铣削振动信号非线性特征的试验研究
硬质合金刀具车削GH2132高温合金磨损及破损试验
An investigation on wear mechanism of high-speed turning of free-cutting steel AISI 1215 using uncoa
Dry Milling of the Ultra-High-Strength Steel 30CrMnSiNi2A with Coated Carbide Inserts
Friction and Wear Performance of Titanium Alloys against Tungsten Carbide under Dry Sliding and Wate
Fabrication of micro DOE using micro tools shaped with focused ion beam
微小型单头错齿滚刀滚齿切削过程建模与仿真
圆弧刃刀具微细非自由切削参数建模与预报
Growth and characterization of Mg(OH)2 film on magnesium alloy AZ31
Formation of an Oxametallacycle Surface Intermeiate via Thermal Activation of 1-Chloro-2-Propanol on
响应曲面法在表面粗糙度预测模型及参数优化中的应用
高强度合金硼铸铁组织成分与切削性能研究
滚压印圆柱母光栅的微刻划制造
Fundamental performance of Magnetic compound Fluid(MCF) wheel in ultra-fine surface finishing of opt
Influence Axial Vibration on Lateral Bending Deformation of Twist Drill in Machining Small Hole
Effect of Low-frequency Pulsed Magnetic Treatment on Micro-hardness of High Speed Steel
A reseach of fracture mechanism in micro cutting of 45 steel based on material properties
磁场分布对磁性复合流体抛光材料去除率的影响
Effect of Powder Pretreatment on the Wear of Ultrafine Cemented Carbide Cutting Inserts
Effect of Grain Growth Inhibitor on the Wear of Ultrafine Cemented Carbide Cutting Inserts
新型微细球端铣刀几何建模与优化设计
微细铣削表面粗糙度预测与试验
Carbon Nanotube’s Modification by Focused Ion Beam Irradiation and Its Healing Strategies
基于人工神经网络的铣削加工变形预测模型
微细铣削振动信号特征参数的主成分分析
典型零件车铣复合加工的运动学特征分析
Thermal activation and reaction of allyl alcohol on Ni(100)
Experiment on Glass Microgroove Molding by Using Polycrystalline Nickel Phosphorus Mold
Experimental Study on Micro-milling of Ti6Al4V with Minimum Quantity Lubrication
基于聚焦离子束铣削技术的微刀具制备
Reserch of dislocation theory in micro cutting
双势阱中冷原子的关联隧穿
干式切削和微量润滑条件下的螺纹车削机理分析及试验研究
基于自适应采样距离场的车铣复合加工中刀具—工件接触几何计算
基于DG／K方法的成形铣刀设计模型
脉冲磁场对高速钢刀具材料微观硬度的影响
斜圆柱结构的新型微细球端铣刀的设计与制造
基于无瞬心包络的微细铣刀螺旋槽刃磨分析
1Cr18Ni9Ti平面铣削中倒棱结构对切削性能影响的试验研究
铣削高强度钛合金TC18的刀具磨损机理
芳纶纤维复合材料切削性能与刀具选用
镁基生物医用材料研究进展
铝7075介观尺度切削过程的仿真研究
小直径麻花钻的钻削仿真与实验研究
精密、超精密切削技术发展概况
切削参数对微细立铣削振动加速度的影响
原子非序列双电离的多次返回碰撞电离机理分析
微细立铣削切削振动试验研究
直槽微铣削中切削参数对铣刀跳动量的影响
锥形球头立铣刀刀刃曲线光滑过渡研究
不锈钢精密车削加工硬化研究
复合粉预处理对WC-10Co超细晶硬质合金刀具寿命的影响
微细刀具的深冷处理研究
金刚石刀具的圆柱母光栅微加工基础研究
Local stress analysis on the cutting edge of the micro-cutting tool
微细切削刀具切削刃局部应力分析
金属切削加工中难加工材料2Cr13的本构模型
基于响应曲面法的微细铣削表面粗糙度预报模型与试验研究
基于电极修整原理的微型刀具制备技术
微细铣削振动信号特征参数的主成分分析(英文)
微细切削刀具及其相关技术研究进展
积屑瘤状态对微细切削表面轮廓特征的影响
微细铣削振动信号非线性特征的试验研究
微小型单头错齿滚刀滚齿切削过程建模与仿真
基于AutoCAD的微小型渐开线齿轮铣刀设计
微细干车削硬铝合金LY12的表面粗糙度研究
微型刀具电火花加工工艺研究
微细铣削表面粗糙度预测与试验
镁基生物医用材料研究进展
氧化亚铁硫杆菌的诱变机理研究
氧化硫硫杆菌和氧化亚铁硫杆菌生物刻蚀加工的协同作用
PCD刀具微细车削硬铝合金的表面质量研究
基于车铣复合加工的微小型结构件工艺研究
期刊信息
  • 《北京理工大学学报》
  • 北大核心期刊（2011版）
  • 主管单位:中华人民共和国工业和信息化部
  • 主办单位:北京理工大学
  • 主编：黄风雷
  • 地址：北京海淀区中关村南大街5号
  • 邮编：100081
  • 邮箱：blgzw@bit.edu.cn
  • 电话：010-68912326 68913988
  • 国际标准刊号：ISSN：1001-0645
  • 国内统一刊号：ISSN：11-2596/T
  • 邮发代号:82-502
  • 获奖情况:
  • 全国优秀高等学校自然科学学报及教育部优秀科技期...,首届国家期刊奖提名奖,中文核心期刊
  • 国内外数据库收录:
  • 俄罗斯文摘杂志,美国化学文摘（网络版）,美国数学评论（网络版）,德国数学文摘,荷兰文摘与引文数据库,美国工程索引,美国剑桥科学文摘,英国科学文摘数据库,日本日本科学技术振兴机构数据库,中国中国科技核心期刊,中国北大核心期刊（2004版）,中国北大核心期刊（2008版）,中国北大核心期刊（2011版）,中国北大核心期刊（2014版）,英国英国皇家化学学会文摘,中国北大核心期刊（2000版）
  • 被引量:17163