欢迎您！东篱公司
退出
-
申报数据库
-
立项数据库
-
成果数据库
-
项目获奖数据库
中文摘要：
为了增大交错互通微通道多孔网格板的机械强度,研究了网格板在拉伸、压缩以及弯曲情况下的力学性能,并建立了相应的理论模型,还对网格板在拉伸、压缩以及弯曲情况下的应力分布情况进行了仿真分析。结果表明,无论是拉伸、压缩还是弯曲,在同样受力F作用时网格板上的最大应力都比同等尺寸致密金属板的应力要大,网格板的机械强度相对致密金属板变小,并且网格板机械强度随着微通道宽度、深度的增大而减小;交错互通微通道多孔网格板在仅受力而未有力矩作用的情况下没有出现应力集中现象,在仅受力矩作用的情况下稍微出现应力集中现象,在同时受到力与力矩的双重作用时出现十分明显的应力集中现象;网格板在微通道宽度较小时更易产生应力集中。
英文摘要：
In order to increase the mechaniacal strength of CCMPMP,mechanical properties of CCMPMP,such as tensile,compressive and bending properties,were investigated theoretically,and the corresponding mechanical models were established.The stress of CCMPMP under the load of tension,compression or bending was simulated respectively.Results show the largest stress of CCMPMP is larger than that of metal plate with the same dimension under the same load of tension,compression or bending,so the mechaniacal strength of CCMPMP is smaller than that of metal plate with the same dimension.And the mechaniacal strength of CCMPMP decreases with the increase of microchannel width and depth.No stress concentration occurs if CCMPMP sustains only forces,small stress concentration occurs if CCMPMP sustains only moments,and large stress concentration occurs if CCMPMP sustains forces and moments simultaneously.In addtion,stress concentration occurs easily when the microchannel width is small.
同期刊论文项目
同项目期刊论文
Fabrication of graphite composite bipolar plate forminiature PEMFCs by micro planing with multi-cutt
Microstructure evolution of adiabatic shear bands and mechanisms of saw-tooth chip formation in mach
Operational characteristics of a passive air-breathing direct methanol fuel cell under various struc
Effect of fabrication parameters on capillary performance of composite wicks for two-phase heat tran
Structural diversity and orientation dependence of a liquid-fed passive air-breathing direct methano
Numerical simulation of transport characteristics of porous metal fiber sintered felts used in micro
Fabrication of wave-like microstructure on the bottom of microflow channel of metallic bipolar plate
Investigation of sintered stainless steel fiber felt as gas diffusion layer in proton exchange membr
An Experimental Investigation on the Fabrication of Micro/meso Surface Features by Metallic Roll-to-
An Innovative Fabrication Process of Porous Metal Fiber Sintered Felts with Three-Dimensional Reticu
Effects of structural parameters on the performance of a micro-reactor with micro-pin-fin arrays (MP
Compressive properties of porous metal fiber sintered sheet produced by solid-state sintering proces
Effects of superimposed high-frequency vibration on deformation of aluminum in micro/meso-scale upse
Cr-N-C multilayer film on 316L stainless steel as bipolar plates for proton exchange membrane fuel c
Study on operational aspects of a passive direct methanol fuel cell incorporating an anodic methanol
Trend prediction in velocity distribution among microchannels based on the analysis of frictional re
Numerical simulation of velocity distribution among microchannels with bifurcation structures as man
Dominance evaluation of structural factors in a passive air-breathing direct methanol fuel cell base
Low temperature solid-phase sintering of sintered metal fibrous media with high specific surface are
Oriented linear cutting fiber sintered felt as an innovative catalyst support for methanol steam ref
Feasibility study of porous copper fiber sintered felt: A novel porous flow field in proton exchange
Effects of structural aspects on the performance of a passive air-breathing direct methanol fuel cel
Electrical-assisted embossing process for fabrication of micro-channels on 316L stainless steel plat
Development and characterization of multilayered Cr-C/a-C:Cr film on 316L stainless steel as bipolar
Study on Shape Error Effect of Metallic Bipolar Plate on the GDL Contact Pressure Distribution in Pr
Optimum design of the slotted-interdigitated channels flow field for proton exchange membrane fuel c
Experimental study of electrical resistivity and flow stress of stainless steel 316L in electroplast
Experimental Study of High-Frequency Vibration Assisted Micro/Mesoscale Forming of Metallic Material
Effect of tip clearance on the heat transfer and pressure drop performance in the micro-reactor with
Acoustic softening and hardening of aluminum in high-frequency vibration-assisted micro/meso Forming
An Experimental Study on Micro Thixoforming Processing Parameters for Reaction Plate with Micro-Pin-
Qualitative investigation on effects of manifold shape on methanol steam reforming for hydrogen prod
Porous Metal-Fiber Sintered Felt by Multi-Tooth Cutting and Sintering-Morphological Analysis and Mec
Characterization of electrical conductivity of porous metal fiber sintered sheet using four-point pr
Characteristics and mechanism of top burr formation in slotting microchannels using arrayed thin slo
Toward using porous metal-fiber sintered plate as anodic methanol barrier in a passive direct methan
Optimization of Catalyst Loading for Porous Copper Fiber Sintered Felts Used in Methanol Steam Refor
Manufacture, characterization and application of porous metal-fiber sintered felt used as mass-trans
期刊信息
位置：