位置：成果数据库 > 期刊 > 期刊详情页
基于Cortex—M3的齿轮传动轴损伤动态监测系统的设计与实现
  • ISSN号：0258-7998
  • 期刊名称：《电子技术应用》
  • 时间：0
  • 分类：TP274.3[自动化与计算机技术—控制科学与工程;自动化与计算机技术—检测技术与自动化装置]
  • 作者机构：[1]重庆大学通信工程学院,重庆400030
  • 相关基金：国家自然科学基金项目（编号：51035008）
作者： 刘晓明[1], 吴德松[1], 王潇瀛[1]
关键词： CORTEX-M3, 局域强信号, 齿轮传动轴, 动态监测, Cortex-M3 , local strong signal , gear shaft , dynamic monitoring
中文摘要：

针对传统的齿轮传动轴监测与诊断系统的局限性，提出了在封闭小体积环境下局域强信号的采集与传输机制。详细论述了系统的工作原理、硬件及软件设计，给出了系统的测试结果。该系统已经成功用于某型汽车发动机传动轴损伤动态监测，对齿轮传动系统的损伤动态监测起到了巨大的推动作用。

英文摘要：

In view of the hmitations of the traditional gear shaft monitoring and diagnosis system, the paper proposes the acquisition and transmission mechanism of the local strong signal in a dosed and small volume environment, discusses in detail the working principle , hardware and software design of the system, and a final test results is given at last. The system has been successfully used in damage dynamic monitoring of a certain type of automobile engine shaft which greatly exposed damage dynamic monitoring of gear transmission system.

同期刊论文项目
基于局域强信号与位域空间变换的关键传动设备故障预示与诊断方法研究
期刊论文 94 会议论文 15 专利 9
同项目期刊论文
基于角域振动信号特征统计量的发动机故障分类方法
An acoustic-structural model for pedestal-radiated noise during ball bearing angular acceleration
Dynamic characteristics of helical gears under sliding friction with spalling defect
CPM信号的定时-相位联合估计算法
基于SOA的设备关键备件虚拟联合库存共享平台研究
基于时频联合的OFDM系统载波频偏估计方案及FPGA实现
粗糙界面法向接触振动响应与能量耗散特性研究
基于非理想Hertz线接触特性的圆柱滚子轴承局部故障动力学建模
A New Model for Relationship Between Vibration Characteristics Caused by Time-Varying Contact Stiff
非连续粗糙多界面接触变形和能量损耗特性研究
Time-Varying Meshing Stiffness Calculation and Vibration Analysis for a 16DOF Dynamic Model With Lin
Application of an improved Levenberg-Marquardt back propagation neural network to gear fault level i
Investigation on skidding of rolling element bearing in loaded zone
An adaptive compression scheme for small-format data of vehicle body base-on sliding window
Multilevel decomposition of vibration signals from motorcycles using the wavelet-Hilbert transformat
Engine fault detection using angle domain signal envelope algorithm
An improved simplex-based adaptive evolutionary digital filter and its application for fault detecti
A new dynamic model for vibration analysis of a ball bearing due to a localized surface defect consi
Vibration analysis of ball bearings with a localized defect applying piecewise response function
应变式二维加速度传感器的研究与仿真
Drive axle housing failure analysis of a mining dump truck based on the load spectrum
无源感应装定系统的改进型传号反转码
H.264中基于边缘方向检测的帧内预测模式选择算法
一种改进的G.729标准固定码本快速搜索算法
Vibration Modeling of Lubricated Rolling Element Bearing Considering Skidding in Loaded Zone
进化论动态参量自适应消噪算法
A method of chatter marks identification based on autocorrelation-threshold
On strain of gear meshing thermo-mechanical coupling
An energy-efficiency wireless sensing method for mechanical failure signals
Dynamic simulation of planetary gear set with flexible spur ring gear
Dynamic and Quasi-Static Modeling of Planetary Gear Set Considering Carrier Misalignment Error and
Study on the chatter vibration of a steel plate mill based on second order cyclic autocorrelation de
Transient meshing performance of gears with different modification coefficients and helical angles u
三维机械差动压电式加速度传感器设计研究
A new method to model a localized surface defect in a cylindrical roller-bearing dynamic simulation
实时视频编码中的低复杂度码率控制算法设计
基于Cortex-M3的齿轮传动轴损伤动态监测系统的设计与实现
SOQPSK信号的定时相位联合估计算法
A Joint Optimization of Momentum Item and Levenberg-Marquardt Algorithm to Level Up the BPNN&#39
Gearbox degradation analysis using narrowband interference cancellation under non-stationary conditi
A new method of accurate broken rotor bar diagnosis based on modulation signal bispectrum analysis o
Accuracy analysis of gear root strain test under different rotational speed
基于CDA和MoG-BBN的齿轮磨损状态识别研究
On the contact stiffness and nonlinear vibration of an elastic body with a rough surface in contact
Vibration characteristic analysis of twenty-high rolling mill with local defect on roll surface base
Dynamic Features of Planetary Gear Train with Tooth Errors
Dynamic simulation of planetary gear with tooth root crack in ring gear
An analytical model to investigate skidding in rolling element bearings during acceleration
Transmission of vibration and energy through layered and jointed plates subjected to shock excitatio
Non-linear dynamic simulation of gear response under the idling condition
一种改进的非局部均值图像去噪算法
基于动态点阵匹配算法的二阶关键词识别
应变片敏感栅结构参数对测量精度的影响
深沟球轴承三维非线性时变振动特性研究
轧辊磨床托瓦松动的动力学建模及振动特性分析
<strong>基于信号特征统计量的发动机故障分类方法研究</strong>
<strong>应变片敏感栅结构参数对测量精度的影响</strong>
基于AS-SOAI算法的内燃机间歇故障诊断方法(英文)
Mesh stiffness calculation of a spur gear pair with tooth profile modification and tooth root crack
Dynamic features of planetary gear set with tooth plastic inclination deformation due to tooth root
基于维护联盟的可重复性维修资源分配优化研究
Prophase failure prediction of the mechanical transmission systems based on the biological evolution
Interference cancellation in space-frequency group codes cooperative OFDM communication with multipl
一种用排队论指导的CAN总线语音通信系统设计
Impulse vibration transmissibility characteristics in the presence of localized surface defects in d
Identification of dissipation of a Hertzian contact from free vibration investigations
Mesh stiffness of an internal spur gear pair with ring gear rim deformation
Dynamic Features of a Planetary Gear System With Tooth Crack Under Different Sizes and Inclination A
The effects of the shape of localized defect in ball bearings on the vibration waveform
Investigation into the energy dissipation of a lap joint using the one-dimensional microslip frictio
Adaptive noise cancellation based on beehive pattern evolutionary digital filter
Characteristic recognition of chatter mark vibration in a rolling mill based on the non-dimensional
应变式三维加速度传感器的设计研究
An ensemble dynamic time domain averaging method for gear fault detection without tachometer
A novel channel estimation method based on compressive sensing for OFDM/OQAM systems
Characteristic recognition of chatter mark vibration in a rolling mill based on non-dimensional para
机电设备维修备件的柔性采购机制与柔性价值
提高声表面波传感器检测精度的方法
基于边缘接触时变刚度的轮齿表面剥落动力学模型与响应特征
斜齿轮齿面剥落故障动力学建模与动态特征研究
Dynamic simulation of spur gear with tooth root crack propagating along tooth width and crack depth
基于混合高斯输出贝叶斯信念网络模型的设备退化状态识别与剩余使用寿命预测方法研究
基于指数平滑和改进增量SVR的齿轮寿命预测研究
MELP低速率语音编码器在DSP上的改进与优化
制造企业可修复备件合理库存优化模型仿真
基于AS—SOAI算法的内燃机间歇故障诊断方法
液压混合动力汽车
Weibull分布下基于遗传算法的设备寿命预测
期刊信息
  • 《电子技术应用》
  • 中国科技核心期刊
  • 主管单位:中国电子信息产业集团有限公司
  • 主办单位:华北计算机系统工程研究所
  • 主编：杨晖
  • 地址：北京市海淀区清华路25号
  • 邮编：100083
  • 邮箱：xinzw@ncse.com.cn
  • 电话：010-66608981 66608982
  • 国际标准刊号：ISSN：0258-7998
  • 国内统一刊号：ISSN：11-2305/TN
  • 邮发代号:2-889
  • 获奖情况:
  • 国家期刊奖,中文核心期刊奖,中国科技期刊奖,电子精品科技期刊
  • 国内外数据库收录:
  • 日本日本科学技术振兴机构数据库,中国中国科技核心期刊,中国北大核心期刊（2004版）,中国北大核心期刊（2008版）,中国北大核心期刊（2011版）,中国北大核心期刊（2014版）,中国北大核心期刊（2000版）
  • 被引量:20858