欢迎您！东篱公司
退出
-
申报数据库
-
立项数据库
-
成果数据库
-
项目获奖数据库
中文摘要：
应用Linkam CSS450剪切仪、广角X射线衍射仪（WAXD）和小角X射线散射仪（SAXS）等研究了剪切对玻璃珠填充聚丙烯结晶行为的影响，结果表明，与纯聚丙烯相比，填加玻璃珠的聚丙烯体系中，玻璃珠起到成核剂的作用，不利于β晶的生成．玻璃珠直径较小（4μm）时，剪切对聚丙烯β晶的生成影响较小；当玻璃珠直径增加到35μm时，剪切速率为20s^-1左右最有利于β晶生成；剪切速率和玻璃珠直径的增加，有利于聚丙烯片晶的取向，而且玻璃珠含量越高，片晶的取向程度越大．
英文摘要：
Linkam CSS450 optical shearing stage, wide-angle X-ray diffraction （WAXD） and small-angle X-ray scattering（SAXS） were used to investigate the effect of shear on crystal structure and crystallization morphology of the glass bead filled polypropylene（PP）. The results indicate that the glass bead worked as nu- cleating agent for the glass bead filled PP, compared with pure PP it restrained the formation of β-crystal after shear treatment. When the mean size of glass bead is smaller （4μm） shear rate had less effect on the formation of β-crystal of PP obviously. However, when the mean size of glass bead is larger（35μm）, it was found that 20 s-1 is an optimal shear rate for the formation of β-crystal. Both shear and glass bead addition could in- duce the orientation of the lamella of the glass bead filled PP. The higher the shear rate and the bigger the glass bead, the higher the orientation of the lamella was.
同期刊论文项目
同项目期刊论文
In-situ observation of drying process of a latex droplet by synchrotron small-angle X-ray scattering
Lattice Boltzmann study of hydrodynamic effects in lamellar ordering process of two-dimensional quen
Tunable wettability by counterion exchange at the surface of electrostatic self-assembled multilayer
Improving performance of polymer photovoltaic devices using an annealing-free approach via construct
Morphology and crystalline transition of poly (3-butylthiophene) associated with its polymorphic mod
Dendritic Superstructures and Structure Transitions of Asymmetric Poly(L-lactide-b-ethylene oxide) D
Combined Effects of Hot Curing Conditions and Reaction Heat on Rubber Vulcanization Efficiency and V
Synchrotron investigation on the sheared structure evolution of syndiotactic polypropylene crystalli
Structural evolution of tensile deformed high-density polyethylene at elevated temperatures: Scannin
Constructing Thin Polythiophene Film Composed of Aligned Lamellae via Controlled Solvent Vapor Treat
Living polymerization of 1,3-butadiene by a Ziegler-Natta type catalyst composed of iron(III) 2-ethy
Styrene polymerization catalyzed by metal porphyrin complex/MAO for in situ synthesizing polystyrene
Structural evolution of tensile-deformed high-density polyethylene during annealing: Scanning synchr
Uniaxial deformation of overstretched polyethylene: In-situ synchrotron small angle X-ray scattering
Phase behavior and dewetting for polymer blend films studied by in situ AFM and XPS: from thin to ul
Study of self-assembly of symmetric coil-rod-coil ABA-type triblock copolymers by self-consistent fi
Study on the formation of beta-crystal during the crystallization process of polypropylene reactor g
Achieving perpendicular alignment of rigid polythiophene backbones to the substrate by using solvent
Shear-enhanced crystallization of a thermoplastic polyimide derived from 3,3 ',4,4 '-oxydiphthalic d
Study of controllable aggregation morphology of ABA amphiphilic triblock copolymer in dilute solutio
External potential dynamics simulation of the compatibility of T-shaped graft copolymer compatibiliz
Preparation and Mechanical Properties of High-Performance Short Ramie Fiber-Reinforced Polypropylene
Hybridization of poly(4-vinyl pyridine)-b-polystyrene-b-poly(4-vinyl pyridine) aggregates in dioxane
Morphological transition of dry vesicles into onion-like multilamellar micelles induced through heat
Effect of binary block-selective solvents on self-assembly of ABA triblock copolymer in dilute solut
Effect of polydispersity on the self-assembly structure of diblock copolymers under various confined
Simulation Study of Aggregate Morphologies Formed by ABC Linear Triblock Copolymers in a Selective S
Thermal properties and crystallization behavior of ultrafine fully-vulcanized powdered rubber partic
期刊信息
位置：