欢迎您！东篱公司
退出
-
申报数据库
-
立项数据库
-
成果数据库
-
项目获奖数据库
中文摘要：
在光学读出非制冷红外热像仪焦平面阵列（FPA，Focal Plane Array）真空封装结构中，硼硅玻璃和双面镀增透膜的锗片分别作为透可见光和透红外光的窗口材料。由于锗窗上增透膜不能承受高温（〈250℃），同时FPA也不能承受高温（〈100℃），因此封装过程须在低温下进行，并对锗窗上的增透膜及FPA进行保护。本文提出了一种用于锗-硼硅玻璃低温扩散焊接的局部加热方法。该方法从导热系数较大的锗窗外表面加热（200℃），而导热系数较小的硼硅玻璃窗口外表面维持低温（60℃）。有限元模拟计算结果表明，该加热过程稳态情况下待焊接区域温度约200℃，满足低温焊接的温度要求。锗窗上温度（200℃）低于250℃，且FPA区域的温升在75℃以下。用实验方法对模拟结果进行了验证，实验结果同模拟结果一致，证明该方法能够有效地保护FPA及锗窗上的增透膜。
英文摘要：
In FPA （Focal Plane A-rray）vacuum packaging of the optical readout uncooled infrared imaging system, Germanium glass with antireflection coatings on both sides and Borosilicate glass are used as the windows for transmitting infrared light and visible light, respectively. Due to the temperature limitation of the antireflection coatings on Germanium glass （〈250℃） and FPA （% 100℃）, the packaging process has to be conducted at low temperature, and thermal protection for FPA and antireflection coatings on Germanium glass must be designed correspondingly. This paper proposes a localized heating method for Germanium-Borosilicate Glass low temperature diffusion bonding. In the present method, Germanium window which has higher thermal conductivity is heated up from its outer surface （200℃）, while the temperature at the outer surface of Borosilicate Glass with lower thermal conductivity is kept lower （60℃）. Finite element simulation results indicate that temperature increase is relatively high in bonding region （200℃）, satisfying the requirement of low temperature bonding, while the temperature of Germanium keeps below 250℃ moreover, the temperature increase in FPA region is relatively low （below 75℃）. Meanwhile, simulation results are consistent with experimental measurement. Therefore, FPA and the antireflection coatings on Germanium can be protected effectively by proposed heating method.
同期刊论文项目
同项目期刊论文
The pressure-dependent performance of a substrate-free focal plane array in an uncooled infrared ima
Development of Protein A Functionalized Microcantilever Immunosensors for the Analyses of Small Mole
Fabrication of high-frequency moire gratings for microscopic deformation measurement using focused i
Study of the performance of different subpixel image correlation methods in 3D digital image correla
Viscoelastic adhesive interfacial model and experimental characterization for interfacial parameters
IDENTIFICATION OF ELASTIC-PLASTIC MECHANICAL PROPERTIES FOR BIMETALLIC SHEETS BY HYBRID-INVERSE APPR
Residual stress in thermal spray coatings measured by curvature based on 3D digital image correlatio
Vibration parameter measurement using the temporal digital hologram sequence and windowed Fourier tr
Evaluation of the quality of a speckle pattern in the digital image correlation method by mean subse
Experimental analysis for the effect of dynamic capillarity on stress transformation in porous silic
Optical readout sensitivity of deformed microreflector for uncooled infrared detector: theoretical m
Performance of an optimized substrate-free focal plane array for optical readout uncooled infrared d
Alternating-current induced thermal fatigue of gold interconnects with nanometer-scale thickness and
A three-dimensional topography measurement for micro-nano film buckling based on the focusing evalua
Investigation of loading and force sensing properties of a probe-type microforce sensor with force-d
Measurement of interfacial toughness of metal film wire and polymer membrane through electricity ind
Deformation mechanisms of carbon nanotube fibres under tensile loading by in situ Raman spectroscopy
位置：