欢迎您！东篱公司
退出
-
申报数据库
-
立项数据库
-
成果数据库
-
项目获奖数据库
中文摘要：
WC-(W,Cr)2C-Ni coating was prepared on 1Cr18Ni9Ti stainless steel and C-276 Ni-base Hastelloy by high velocity oxy-fuel(HVOF)spraying.The effect of post heat treatment in air atmosphere on the microstructure,phase composition,microhardness,fracture toughness,and wear resistance of HVOF-sprayed WC-(W,Cr)2C-Ni coating was investigated.The microstructure and phase composition of the coatings were analyzed by means of field emission scanning electron microscopy(FESEM)and X-ray diffraction(XRD).The microhardness and fracture toughness of the coatings were measured using a microhardness tester and a Vickers hardness tester.Moreover,dry friction and wear behavior of the coatings sliding against Si3N4 ball was investigated using an oscillating friction and wear tester;and the worn surfaces of the coatings were analyzed by means of scanning electron microscopy(SEM).It was found that heat treatment within 500-800°C resulted in crystallization of amorphous phase in as-sprayed coating,generating nanoscale new phases such as NiWO4,CrWO4 and Cr2WO6.Besides,heat treatment led to increase of the microhardness of as-sprayed coating,and the highest microhardness was obtained after heat treatment at 800°C.The fracture toughness and wear resistance of the as-sprayed coating increased with increasing heat treatment temperature up to 700°C but tended to decrease with further elevating temperature.In other words,the mechanical properties and wear resistance of the as-sprayed coatings were worsened owing to excessive growth of oxidation grains and depletion of ductile Ni binder after heat treatment above 700°C.Thus it was suggested that as-sprayed ceramic composite coating should be post heat treated in air at a moderate temperature of 700°C so as to achieve the optimized mechanical properties and wear resistance.
英文摘要：
WC-(W,Cr)2C-Ni coating was prepared on 1Cr18Ni9Ti stainless steel and C-276 Ni-base Hastelloy by high velocity oxy-fuel(HVOF)spraying.The effect of post heat treatment in air atmosphere on the microstructure,phase composition,microhardness,fracture toughness,and wear resistance of HVOF-sprayed WC-(W,Cr)2C-Ni coating was investigated.The microstructure and phase composition of the coatings were analyzed by means of field emission scanning electron microscopy(FESEM)and X-ray diffraction(XRD).The microhardness and fracture toughness of the coatings were measured using a microhardness tester and a Vickers hardness tester.Moreover,dry friction and wear behavior of the coatings sliding against Si3N4 ball was investigated using an oscillating friction and wear tester;and the worn surfaces of the coatings were analyzed by means of scanning electron microscopy(SEM).It was found that heat treatment within 500-800°C resulted in crystallization of amorphous phase in as-sprayed coating,generating nanoscale new phases such as NiWO4,CrWO4 and Cr2WO6.Besides,heat treatment led to increase of the microhardness of as-sprayed coating,and the highest microhardness was obtained after heat treatment at 800°C.The fracture toughness and wear resistance of the as-sprayed coating increased with increasing heat treatment temperature up to 700°C but tended to decrease with further elevating temperature.In other words,the mechanical properties and wear resistance of the as-sprayed coatings were worsened owing to excessive growth of oxidation grains and depletion of ductile Ni binder after heat treatment above 700°C.Thus it was suggested that as-sprayed ceramic composite coating should be post heat treated in air at a moderate temperature of 700°C so as to achieve the optimized mechanical properties and wear resistance.
同期刊论文项目
同项目期刊论文
Preparation and nano/microtribological properties of perfluorododecanoic acid (PFDA)/3/aminopropyltr
Doping of carbon ?ber into polybenzimidazole matrix and mechanical properties of structural carbon ?
Electrochemical corrosion behavior of chromium–phosphorus coatings electrodeposited from trivalent c
Imidazolium hexa?uorophosphate ionic liquids as high temperature lubricants for steel–steel contacts
Preparation of shuttle/like Sb2S3 nanorod/bundles via a solvothermal approach under alkaline conditi
Microstructure,tribological behavior,and corrosion/resistant performance of bonded Mos2 solid lubric
Multi/walled carbon nanotube supported Pd and Pt nanoparticles with high solution af?nity for effect
Fabrication of an intelligent superhydrophobic surface based on ZnO nanorod arrays with switchable a
Molecular dynamical simulations on a/C:H film growth from C and H atomic flux: efect of incident ene
Study on the superhydrophobic poly(methyl methacrylate)/silver thiolate composite coating with absor
In?uence of heat treatment on the micro/nano/tribological properties of ultra/thin ionic liquid ?lms
Preparation of shuttle-like Sb2S3 nanorod-bundles via a solvothermal approach under alkaline conditi
Electrochemical growth of ?owerlike gold nanoparticles on polydopamine modi?ed ITO glass for SERS ap
Fullerene/like hydrogenated carbon ?lms with super/low friction and wear, and low sensitivity to env
Study on the friction and wear behavior of basalt fabric composites ?lled with graphite and nano/SiO
Preparation, damping and thermal properties of potassium titanate whiskers ?lled castor oil/based po
Microsliding wear behaviour of HVOF sprayed conventional and nanostructured WC–12Cocoatings at eleva
Reversible conversion of water/droplet mobility from rollable to pinned on a superhydrophobic functi
Microstructure and mechanical behaviour of nano-eutectic Fe83B17 alloy prepared by a self-propagatin
Friction and wear properties of combined surface modi?ed carbon fabric reinforced phenolic composite
Synthesis and characterization of anatase TiO2 nanotubes and their use in dye-sensitized solar cells
Effect of polytetrafluoroethylene gradient-distribution on the hydrophobic and tribological properti
The Influence of Plasma Treatment on the Tribological Properties of Hybrid PTFE/Cotton Fabric/Phenol
Influences of bias voltage on mechanical and tribological properties of Ti-Al-C films synthesized by
Study on the tribological behavior of hybrid PTFE/cotton fabric composites filled with Sb2O3 and mel
In?uences of ultraviolet irradiation on structure and tribological properties of diamond/like carbon
Fabrication of stable, transparent and superhydrophobic nanocomposite ?lms with polystyrene function
TiO2 nanotubes with tunable morphology, diameter, and length: synthesis and photo/electrical/catalyt
Effect of anion on micro/nano/tribological properties of ultra/thin imidazolium ionic liquid films o
Structural, mechanical and tribological characterizations of a/C:H:Si films prepared by a hybrid PEC
Preparation and characterization of reactively sintered Ni3Al–hBN–Ag composite coating on Ni/based s
Effects of pulse bias duty cycle on fullerene/like nanostructure and mechanical properties of hydrog
Shell–core–corona aggregates formed from poly(styrene)/poly(4/vinylpyridine) block copolymer induced
A replication strategy for complex micro/nanostructures with superhydrophobicity and superoleophobic
The chemical composition and bonding structureof B–C–N–Hthin?lmsdepositedby reactivemagnetron sputte
Bisimidazolium ionic liquids as the high/performance antiwear additives in poly(ethylene glycol) for
In?uence of nanometer lanthanum ?uoride on friction and wear behaviors of bonded molybdenum disul?de
An investigation of friction and wear performances of bonded molybdenum disul?de solid ?lm lubricant
Effect of Ag nanoparticles additive on the tribological behavior of multialkylated cyclopentanes (MA
Tribological Behavior of Plasma Nitrided 1Cr18Ni9Ti Austenitic Stainless Steel Under the Effect of L
Effects of carbon fiber surface treatment on the tribological properties of 2D woven carbon abric/po
Synthesis of water/soluble carbon nanotubes via surface initiated redox polymerization and their tri
Electrochemical and photochemical characterization of novel ferrocenyl–azobenzene labeled PNA monome
Effect of deposition pressure on the adhesion and tribological properties of a/CNxH films prepared b
Electrochemical characterization of the solution accessibility of CaTiO3 microstructures and improve
Tribology properties of plasma sprayed nanostructured and conventional WC/Co coatings under water en
Functionalization of multiwalled carbon nanotube via surface reversible addition fragmentation chain
Polyelectrolyte/grafted carbon nanotubes: synthesis,reversible phase/transition behavior, and tribol
Fabrication of bulk Al2O3 dispersed ultrafine/grained Cu matrix composite by self/propagating high/t
The preparation of CeF3 nanocluster capped with oleic acid by extraction method and application to l
Microstructure and tribological properties of in situ synthesized TiN/Ti3Al intermetallic matrix com
Large/scale Fe/C nanoeutectic alloy prepared by a self/propagating high/temperature synthesis castin
Change of surface chemical structure and composition of phenolphthalein poly(ethersulfone) in differ
Effect of carbon fiber surface treatments on the flexural strength and tribological properties of sh
Tribological properties of titanium aluminides coatings produced on pure Ti by laser surface alloyin
Tribological characterisation of electrodeposited nickel/titania nanocomposite coatings sliding agai
Tribological evaluation of α,?/diimidazoliumalkylenehexa?uorophosphate ionic liquid and benzotriazol
Correlation between the structure and wear behavior of chromium coatings electrodeposited from triva
Effect of the anion on the tribological properties of ionic liquid nano/films on surface/modified si
Friction and wear behavior of hybrid glass/PTFE fabric composite reinforced with surface modified na
Tribological behavior of hybrid glass/PTFE fabric composites with phenolic resin binder and nano TiO
Tribological behaviors of fullerene/like hydrogenated carbon (FL/C:H) ?lm in different atmospheres s
Design and fabrication of nanopillar patterned au textures for improving nanotribological performanc
期刊信息
位置：