位置：成果数据库 > 期刊 > 期刊详情页
采用Ag-Cu-Ti＋Mo复合钎料钎焊Si3N4陶瓷
  • ISSN号：0253-360X
  • 期刊名称：《焊接学报》
  • 时间：0
  • 分类：TG425[金属学及工艺—焊接]
  • 作者机构：[1]哈尔滨工业大学材料科学与工程学院,哈尔滨150001
  • 相关基金：国家自然科学基金资助项目（50975064,51021002,50902029）
作者： 贺艳明[1], 王兴[1], 王国超[1], 王天鹏[1]
关键词： SI3N4陶瓷, 钎焊, Ag-Cu-Ti+Mo复合钎料, 纳米压痕, 力学性能
中文摘要：

采用Ag-Cu-Ti＋Mo复合钎料连接Si3N4陶瓷,利用SEM,TEM,Nanoindentation研究了钎料内钼颗粒含量对接头组织和力学性能的影响.结果表明,在Si3N4/钎料界面处形成了一层致密的反应层,该反应层由TiN和Ti5Si3组成.接头的中间部分由银基固溶体、铜基固溶体、钼颗粒和Ti-Cu金属间化合物组成.借助于纳米压痕技术测定了接头内Ti-Cu化合物以及钎料金属的弹性模量和硬度值.随着钎料内钼颗粒含量的提高,母材/钎料界面反应层厚度逐渐降低;钎料金属中Ti-Cu化合物数量增多;此外,银和铜基固溶体组织逐渐变得细小.当添加5%Mo时,得到最高的接头强度429.4 MPa,该强度相比合金钎料提高了114.7%.

同期刊论文项目
多功能防热陶瓷基复合材料研究
期刊论文 209 专利 54
使用功能梯度钎料连接氮化硅与耐热钢的机理研究
期刊论文 13 会议论文 1 专利 1 著作 1
以SiAlON陶瓷-玻璃为中间层连接氮化硅陶瓷的工艺与机理研究
期刊论文 7 会议论文 2
同项目期刊论文
TiAl/Ni基合金反应钎焊接头的微观组织及剪切强度(英文)
TiAl基合金与Ni基合金钎焊连接接头界面组织及性能
TiB_w/TC4钛合金与C/C复合材料钎焊接头的界面组织结构
Al_2O_3/Cu-Sn-Ti+B钎料/Ti-6Al-4V合金连接的微观结构及力学性能
连接工艺参数对镍基高温合金TLP连接接头组织和性能的影响(英文)
TiAl合金与镍基高温合金的扩散连接
Microstructure and mechanical properties of Si3N4/42CrMo joint brazed with TiNp modified active fill
Effect of SiC content on mechanical properties and thermal shock resistance of BN–ZrO2–S
In?uence of reactive melt in?ltration parameters on microstructure and properties of low temperature
Effect of ZrO2 content on microstructure, mechanical properties and thermal shock resistance of (ZrB
Synthesis route and mechanical properties of reactive hot pressed TiN-TiB2 ceramics.
Influence of Composition on Self-toughening and Oxidation Properties of Y-α-Sialons.
Influence of Composition on Self-toughening and Oxidation Properties of Y-α-Sialons
Preparation, structure and electrical conductivity of pyrochlore-type samarium–lanthanum zirco
Improvement of mechanical properties of Sn−58Bi alloy with multi-walled carbon nanotubes
Ionic conductivity of oxy-apatite La10Si6-xInxO27-δ solid electrolyte ceramics
High voltage asymmetric supercapacitor based on MnO2 and graphene electrodes.
Performances of high voltage electrochemical capacitor using ball-milled graphite/Mn3O4 composite el
Preparation, characterization and infrared emissivity properties of polymer derived coating formed o
The structure and in vitro apatite formation ability of porous titanium covered bioactive microarc o
Microarc oxidized TiO2 based ceramic coatings combined with cefazolin sodium/chitosan composited dru
The effect of titanium bead diameter of porous titanium on the formation of micro-arc oxidized TiO2-
The effect of oxidation time on the micro-arc titanium dioxide surface coating containing Si,Ca and
Effect of holding time on microstructure and mechanical properties of Si3N4/Si3N4 joints brazed with
Microstructure evolution of the Si3N4/Si3N4 joints brazed using Au-Ni-V filler alloys with different
Uncovering the critical factor in determining the residual stresses level in Si3N4-GM filler alloy-4
An analysis of deformation mechanism in the Si3N4-AgCuTi+SiCp-Si3N4 joints by digital image correlat
Microstructure and strength of Si3N4 joints bonded with sialon-oxinitride glass.
Effect of joining temperature and holding time on microstructure and shear strength of Ti2AlC/Cu joi
Investigation of Si3N4 cramice/42CrMo steel joints brazed with Ag-Cu-Ti brazing alloy plus WC partic
原位形成氧氮玻璃中间层连接Si3N4陶瓷
Effect of brazing temperature on microstructure and mechanical properties of grapgine/copper joint.
用Ag-Cu-Ti+Mo复合钎料钎焊Si3N4陶瓷
Influence of ZrC content on the elevated temperature tensile properties of ZrCp/W composites
Inhibiting Effect of Additives on Formation of ZrC Phase in ZrB2–BN Composites by Reactive Hot Press
Carbon microtube/Fe3O4 nanocomposite with improved wave-absorbing performance
First-principles investigation of ammonia borane for hydrogen storage
Synthesis of nitrogen-doped carbon microtubes for application in lithium batteries
Preparation of SiCN(O) material with vinyl trichlorosilicane
Influence of doping with various cations on electrical conductivity of apatite-type neodymium silica
Electrical conductivity and chemical stability of BaCe0.8–xAxGd0.2O3–δ (A = In, Zr, Ta; x = 0, 0.1)
Friction and wear properties of hot-pressed NiCr-BaCr2O4 high temperature self-lubricating composite
Microstructure, thermal shock resistance and thermal emissivity of plasmas sprayed LaMAl11O19 (M = M
Enhanced sinterability and electrical properties of GdSmZr2O7 by addition of nickel oxide.
Influences of temperature and atmosphere on thermal stability of BaCrO4.
Influences of lattice vibration and electron transition on thermal emissivity of Nd3+ doped LaMgAl11
Synthesis and photoluminescence properties of Eu3+?-doped Gd2Zr2O7
Preparation, structural characterization and enhanced electrical conductivity of pyrochlore-type (Sm
Physical and surface characteristics of the mechanically alloyed SiBCN powder.
Microstructural features and properties of the nano-crystalline SiC/BN(C) composite ceramic prepared
Formation of Concentric Multilayers in a Chitosan Hydrogel Inspired by Liesegang Ring Phenomena
Magnetic Hydrogels and Their Potential Biomedical Applications.
Influence of sintering parameters on microstructure and electrical conductivity of La10Si6O27 cerami
Preparation and characterization of LnMgAl11O19 (Ln = La, Nd, Gd) ceramic powders.
Sintering and electrical conductivity of the GdSmZr2O7 ceramic with and without ZnO sintering aid.
Hot corrosion behavior of neodymium magnesium hexaaluminate by vanadium pentoxide in air
Influence of calcination temperature on synthesis and photoluminescence properties of Eu3+?-doped La
A new approach for the net-shape fabrication of porous Si3N4 bonded SiC ceramics with high strength
Fabrication of a new SiC/2024Al co-continuous composite with lamellar microstructure and high mechan
Development of elongated 6H-SiC grains in reaction-bonded porous SiC ceramics
Densification of tantalum carbide ceramics with 5 mol.% Al, Cu, Ag and Au
Structure and electrical conductivity of BaCe0.85Ln0.15O3–δ (Ln = Gd, Y, Yb) ceramics.
Growth of YbVO4 crystals evolved from hot corrosion reactions of Yb2Zr2O7 against V2O5 and Na2SO4+V2
Domain structures in hot-press sintered SrBi2Ta1.6Nb0.4O9 and SrBi2Ta2O9
Hollow graphene spheres self-assembled from graphene oxide sheets by a one-step hydrothermal process
Dependence of infrared radiation on microstructure of polymer derived ceramic coating on steel.
Microstructure and shear strength of the reactive brazing joints of TiAl/Ni-based alloy
Improving the strength of brazed joints with in situ synthesized TiB whiskers
Cu+TiB2 composite filler for brazing Al2O3 and Ti-6Al-4V alloy
In situ synthesis of TiB whisker reinforcements in the joints of Al2O3/TC4 during brazing
Microstructure evolution of Al2O3/Al2O3 joint brazed with Ag-Cu-Ti+B+TiH2 composite filler
Brazing of Al2O3 to Ti–6Al–4V alloy with in situ synthesized TiB-whisker-reinforced acti
Sn-Zn合金在Si3N4/2024Al材料表面渗Sn行为研究
工艺参数对过渡液相扩散连接TiAl 基合金界面组织及接头强度的影响
用复合中间层扩散连接TiAl基合金与Ni基合金
工艺参数对Al2O3/TC4接头界面组织及力学性能的影响.
Cu+B复合钎料配比对Al2O3/TC4合金钎焊接头界面组织的影响.
GH99 合金液相扩散连接界面组织分析
保温时间对TiAl与Ni基合金扩散连接界面组织结构及连接强度的影响
Al2O3/Cu-Sn-Ti+B钎料/Ti-6Al-4V 合金连接的微观结构及力学性能
TiBw/TC4 钛合金与C/C复合材料钎焊接头的界面组织结构
Influence of residual stress on magnetoelectric coupling of bilayered CoFe2O4/PMN-PT thin films.
ol-gel synthesis of Bi3.25La0.75Ti3O12 nanotubes
Effects of Ar ion irradiation on the diffusion bonding joints of Zr55Cu30Ni5Al10 bulk metallic glass
Effect of hydrogen on diffusion bonding of TiAl-based intermetallics and Ni-based superalloy using h
Microstructure evolution and its effect on the mechanical properties of the ZrC-SiC composite joint
Interfacial Structure and Shear Strength of Brazing Joints of TiAl/Ni-based Alloy
Molecular dynamics simulation of linear friction welding between dissimilar Ti-based alloys
Morphology Characterization of Multi-Walled Carbon Nanotubes in Sn–58Bi/CNTs Composites
Microstructure and Properties of the Diffusion Bonding ZrB2-SiC/Nb Joint
Joint properties between carbon nanotube and gold at different energy levels from molecular dynamics
Microstructure evolution and mechanical properties of transient liquid phase (TLP) bonded joints of
Effects of alloying elements in GH99 superalloy on microstructure evolution of reactive brazing TiAl
Effect of Preforming Process and Starting Fused SiO2 Particle Size on Microstructure and Mechanical
Microstructural features and properties of nano-crystalline SiC/BN(C) composite ceramic prepared fro
Effect of BN content on microstructures, mechanical and dielectric properties of porous BN/Si3N4 com
Microstructure and integrity of leucite ceramic derived from potassium-based geopolymer precursor
Mechanical and dielectric properties of gelcasted Si3N4 porous ceramic using CaHPO4 as an additive
Mechanical and thermal physical properties of amorphous SiCN(O) ceramic bulks prepared by hot-press
Oxidation of ZrC-30vol% SiC composite in air from low to ultrahigh temperature
Effect of solid contents on the mechanical properties of SiC-10 wt.%AlN ceramic composites prepared
Mechanical properties and plasma erosion resistance of BNp/Al2O3-SiO2 composite ceramics
Effect of Starting PMMA Content on Microstructure and Properties of Gel Casting BN/Si3N4 Ceramics wi
Influence of trivalent Gd and Dy codoping on the structure and electrical conductivity of pyrochlore
Preparation and high temperature oxidation resistance of microarc oxidation ceramic coatings formed
Friction and wear characteristics of BaCr2O4 ceramics at elevated temperatures in sliding against si
Effect of Ce substitution for Zr on electrical property of fluorite-type Gd2Zr2O7.
Electrical conductivity improvement of Nd2Ce2O7 ceramic co-doped with Gd2O3 and ZrO2.
The effect of co-doping with MgO and Yb2O3 on the structure and electrical conductivity of the Sm2Zr
Order-disorder transformation and enhanced oxide-ionic conductivity of (Sm1–xDyx)2Zr2O7 ceramics
Interfacial microstructure and mechanical properties of TiAl and C/SiC joint brazed with TiH2–
Microstructure and mechanical properties of active brazed SiO2–BN ceramic modified by electron
Interlayer design to control interfacial microstructure and improve mechanical properties of active
Correlation between microstructure and mechanical properties of active brazed Invar/SiO2–BN jo
Interfacial microstructure and strengthening mechanism of BN-doped metal brazed Ti/SiO2-BN joints
Microstructure and mechanical properties of diffusion bonded single crystal to polycrystalline Ni-ba
Low temperature diffusion bonding of pure aluminum
Microstructure and Mechanical Properties of ZrC-W Matrix Composite Prepared by Reactive Infiltration
烧结温度对W-10Ti显微组织和硬度的影响.
Preparation of BaCrO4 particles in the presence of EDTA from aqueous solutions.
Synthesis and electrical conductivity of La10Si5.5B0.5O27+δ (B = In, Si, Sn, Nb) ceramics.
Influence of magnesia doping on structure and electrical conductivity of pyrochlore-type GdSmZr2O7.
Synthesis, structure and electrical conductivity of BaZr1–xDyxO3–δ ceramics
Synthesis, structure and electrical properties of rare-earth doped apatite-type lanthanum silicates
Hot corrosion of (Sm1–xYbx)2Zr2O7 (x = 0, 0.5, 1.0) ceramics against V2O5 molten salt in air at 800
Thermo-optical properties of LaMAl11O19 (M = Mg, Mn, Fe) hexaaluminates for high-temperature thermal
Preparation, structure and electrical conductivity of pyrochlore-type Gd1–xEu2xSm1–xZr2O7 ceramics w
Electrodeposition and tribological properties of self-lubricating Ni–BaCr2O4 composite coatings
Friction and wear properties of reactive hot-pressed TiB2-TiN composites in sliding against Al2O3 ba
Preparation, structure and electrical conductivity of the pyrochlore-type phase Sm2Zr2O7 codoped wit
Thermo-optical properties of LaMg1–xNixAl11O19 (0 ≤ x ≤ 1.0) hexaaluminates for metallic
Microstructure and mechanical properties of zirconia-toughened lithium disilicate glasseceramic comp
Electrical conductivity of 5 mol.% Yb2O3 and 5 mol.% Gd2O3 co-doped Sm2Zr2O7
Effect of brazing conditions on microstructure and mechanical properties of Al2O3/Ti-6Al-4V alloy jo
ZrC-W复合材料的无压反应浸渗制备工艺研究
Hot corrosion of V2O5-coated NdMgAl11O19 ceramic in air at 950 oC
Microstructure and mechanical properties of an Si3N4/Si3N4 joint brazed with Au-Ni-Pd-V filler alloy
Effect of sintering pressure on the texture of hot-press sintered hexagonal boron nitride composite
Preparation and thermophysical properties of LaMgAl11O19–Yb3Al5O12 ceramic composites.
Effect of bonding parameters on microstructures and properties during TLP bonding of Ni-based alloy
Molecular dynamics simulation of the effect of surface roughness and pore on linear friction welding
In Vitro Cell Uptake of Biocompatible Magnetite/Chitosan Nanoparticles with High Magnetization: A Si
A metasilicate-based ceramic coating formed on magnesium alloy by microarc oxidation and its corrosi
Microarc oxidation of 2024 Al alloy using spraying polar and its influence on microstructure and cor
Crystallization and microstructural evolution process from mechanically alloyed amorphous SiBCN powd
Structure and electrical conductivity of BaCe0.7In0.1A0.2O3–δ (A = Gd, Y) ceramics.
Effect of in situ synthesized TiB whisker on microstructure and mechanical properties of carbon&ndas
纳米结构多层膜自蔓延连接技术的研究及其应用.
Effects of Pore size on Microstructure, Mechanical and Dielectric Properties of Gel Casting BN/Si3N4
Microstructure and integrity of leucite ceramic derived from potassium-based geopolymer precursor.
Microstructural evolution and growth behavior of in situ TiB whisker array in ZrB2-SiC/Ti6Al4V brazi
Interfacial Structure and Properties of Reactive Brazing Joints of TiAl/Ni-based Alloy
Diffusion bonding of ZrB2-SiC/Nb with in situ synthesized TiB whiskers array
Dense sub-micron-sized ZrC-W composite produced by reactive melt infiltration at 1200 oC.
含碳纳米管的Sn-58Bi钎料的制备及其钎焊性研究
In?uence of brick pattern interface structure on mechanical properties of continuous carbon ?ber rei
Study on hot corrosion reactions between SmYbZr2O7 ceramic and vanadium pentoxide at temperatures of
Microstructure and tribological properties of reactive hot pressed TiN-TiB2 composites incorporated
Ti-Ni钎料钎焊连接 ZrC-SiC 复合陶瓷接头的界面组织
First-principles calculations of water dissociation on the oxygen-deficient (010) surface in Ferguso
TiAl 合金与镍基高温合金的扩散连接
An elevated temperature infrared emissivity ceramic coating formed on 2024 aluminium alloy by microa
Ball-milled graphite as an electrode material for high voltage supercapacitor in neutral aqueous ele
Physical and surface characteristics of the mechanically alloyed SiBCN powder
Electrical properties of the GdSmZr2O7 ceramic under different sintering conditions
Diffusion bonding of ZrB2-SiC and Nb using dynamic compressed Ni foam interlayer
Ternary Phase ZrxCuyCz in Reactively Infiltrated ZrC/W Composite.
薄带连铸用侧封板材料的研究进展
ZrC—SiC复合陶瓷扩散焊接头界面组织及力学性能
Ti-Ni钎料钎焊连接ZrC—SiC复合陶瓷接头的界面组织
Improvement of mechanical properties of Sn-58Bi alloy with multi-walled carbon nanotubes
纳米尺度连接技术的研究现状与展望
用复合中间层扩散连接钛铝基合金与镍基合金
工艺参数对Al2O3／TC4合金接头界面组织及力学性能的影响
SiC陶瓷及其复合材料连接的研究现状
Cu＋B复合钎料配比对Al2O3／TC4合金钎焊接头界面组织的影响
非晶态镍基钎料箔润湿成缝特征及其对钎焊接头形态的影响
TiAl/Ti/GH99扩散连接接头应力的数值模拟
水轮机叶片热喷涂技术研究现状及展望
电子封装与组装中的软钎焊技术发展及展望
非晶合金连接的进展现状
Ag-Cu-Sn-Ti活性钎焊Gr/2024Al复合材料与TC4钛合金
DD3高温合金与Ti3AlC2陶瓷的真空钎焊
Cu-25Sn-10Ti活性钎焊SiO2f／SiO2复合材料与Invar合金
含碳纳米管的Sn-58Bi钎料的制备及其钎焊性
纳米Al_2O_3/GdAlO_3共晶陶瓷复合粉体的醇-水加热法制备与表征
先驱体法制备非晶态SiCNO材料
纳米结构多层膜自蔓延连接技术的研究及其应用
Cuf/铝硅酸盐聚合物复合材料的制备和力学性能
漂珠尺寸对35%漂珠/铝硅酸盐聚合物复合材料组织结构与性能的影响
微弧氧化生物活性TiO2基纳米结构表面磷灰石诱导能力与药物上载及释放
AlN添加量对BN基复合陶瓷物相组成、微观结构及力学性能的影响
Mechanical properties and plasma erosion resistance of BNp/Al2O3-SiO2 composite ceramics
AlN添加量对BN基复合陶瓷热学性能与抗热震性的影响
TiAl与Ni基合金接触反应钎焊接头界面组织及性能
Cr含量对（TiBw＋TiCp）／（Ti-4．0Fe-7．3Mo-xCr）复合材料组织及性能的影响
Effect ofjoiningtemperatureandholdingtimeonmicrostructureandshear strength ofTi2AlC/Cu jointsbrasedu
原位形成氧氮玻璃中间层连接Si3N4陶瓷
Interfacial microstructure of Si3N4/Si3N4 joint brazed using Au-Ni-V filler alloy
An analysis of deformation mechansm in the Si3N4-AgCuTi+SiCp-Si3N4 joints by digital image correlati
Effect of brazing temperature on microstructure and mechanical properties of Si3N4/Si3N4 joints braz
Microstructural and mechanical characterization of the Si3N4/Si3N4 joint brazed using Au-Ni-V filler
Microstructure and mechanical properties of the Si3N4/42CrMo steel joints brazed with Ag-Cu-Ti plus
Si3N4与42CrMo钢的连接钎料和钎焊连接方法
Microstructure and mechanical properties of Si3N4/Si3N4 joint brazed with Ag-Cu-Ti plus SiCp composi
Uncovering the critical factor in determining the residual stress level in Si3N4-GM filler alloy-42C
Microstructure evolution of Si3N4/Si3N4 joint brazed with Ag-Cu-Ti plus SiCp composite filler
Revealing the strengthening mechanism in Si3N4 ceramic joint by atomic force microscopy coupled with
RE-Si-Al-O-N（RE=Y或Lu）连接Si3N4陶瓷接头的微观组织与性能
期刊信息
  • 《焊接学报》
  • 北大核心期刊（2011版）
  • 主管单位:中国科学技术协会
  • 主办单位:中国机械工程学会 中国机械工程深地焊接学会 哈尔滨焊接研究所
  • 主编：王亚
  • 地址：哈尔滨市松北区创新路2077号
  • 邮编：150028
  • 邮箱：hjxbbjb@126.com
  • 电话：0451-86323218
  • 国际标准刊号：ISSN：0253-360X
  • 国内统一刊号：ISSN：23-1178/TG
  • 邮发代号:14-17
  • 获奖情况:
  • 1990年获机械电子工业部年度优秀科技期刊二等奖,1992年获中国科学技术协会优秀学术期刊三等奖
  • 国内外数据库收录:
  • 美国化学文摘（网络版）,荷兰文摘与引文数据库,美国工程索引,日本日本科学技术振兴机构数据库,中国中国科技核心期刊,中国北大核心期刊（2004版）,中国北大核心期刊（2008版）,中国北大核心期刊（2011版）,中国北大核心期刊（2014版）,中国北大核心期刊（2000版）
  • 被引量:15422